HSY HSY Clean Cleanroom swabs · Suzhou, China
Products

Thirteen models, grouped the way a line is actually set up.

Not by price, and not by a colour code borrowed from another maker. By shaft diameter and shaft length — the two things that decide whether a swab reaches the feature and whether your fixture holds it.

CS15-001Spherical76 ±1.0φ3.2 ±0.512 ±1.0 headCS15-002Spherical75 ±1.0φ2.6 ±0.512 ±1.0 headCS15-003Tapered78 ±1.0φ3.0 ±0.510 ±1.0 headCS15-005Turned-down78 ±1.0φ2.1 ±0.17 ±1.0 headCS15-006Flat-trimmed75.5 ±1.0φ2.0 ±0.28 ±1.0 headCS15-009Ultra-fine74 ±1.0φ1.1 ±0.25 ±1.0 headAll rows share one scale — lengths compare directly. Shaft starts inside the cotton.
Fig. 3 The CS15 range at true scale. Tip geometry, not shaft length, is what changes across these six — every one is a 73 mm shaft at φ1.57 mm.
Tip geometry What it is for Models
Spherical General cleaning, blind-hole bottoms, connector cavities. Rounded end, no edge to catch on a wall. 001 · 002
Tapered Edges and corners where the head has to reach past an obstruction. 003
Turned-down Very narrow gaps. The shaft end is turned down before the cotton goes on, so the head narrows without losing cotton pick-up. 005
Flat-trimmed Flat surfaces where full contact matters more than penetration. 006
Ultra-fine φ1.1 mm — micro-vias, fibre end-faces, fine-pitch contacts. The finest tip we run. 009

CS15

3-inch, φ1.57 mm shaft

Precision cleaning of small features — PCB, optics, sensors, connectors. Six tip geometries on one shaft, so a single fixture covers the whole range.

  • CS15-001Sphericalφ3.2±0.576±1.0
  • CS15-002Sphericalφ2.6±0.575±1.0
  • CS15-003Taperedφ3.0±0.578±1.0
  • CS15-005Turned-downφ2.1±0.178±1.0
  • CS15-006Flat-trimmedφ2.0±0.275.5±1.0
  • CS15-009Ultra-fineφ1.1±0.274±1.0

CS25

3-inch, φ2.46 mm shaft

Larger head, heavier solvent load — for wider surfaces, chamber walls, stencil and fixture cleaning where a smaller head cannot hold enough liquid.

  • CS25-001Sphericalφ4.576.0±0.8
  • CS25-002Sphericalφ4.781±1.0

6 in

6-inch long shaft

Reach without leaning into the tool. The CS25-003 uses a knurled hardwood shaft at φ2.3 mm — hardwood is stiffer than paper at the same diameter, so the shaft stays thinner and still resists bending.

  • CS25-003Sphericalφ4.7150.0±0.5
  • CS25-005Sphericalφ4.6149.5±1.0
  • CS25-006Sphericalφ5.0150.0±1.0
Notes

Two variants we quote on request.

CS25-005D and CS25-092D carry a D suffix. On the models where that suffix matches a part number you already buy, we quote against your drawing rather than ours — the suffix has meant more than one thing across suppliers, and we would rather confirm than assume.

Packing

Carton counts, stated plainly.

CS15 series ships 50,000 pcs per carton; CS25 standard 25,000; the 6-inch range 20,000. If your container planning assumes a different carton count, tell us — the pack count can follow your line rather than ours.

Next step

Send us the drawing you buy against today.

We will confirm fit model by model, or tell you where we differ — before you spend money on samples. If it lines up, we send a benchmark kit: three models, three packs each, and a comparison card with a blank column for your own limits.